FAQ

Freqently asked questions.

Please choose your topic:

In General

Logo
  1. CAN bus wiring test
  2. CAN Symboleditor Manual
  3. CANBUSview XL III, CAN Quick Tester C-QT15 and DeviceNet Analyzer
  4. CANtouch vs. CAN-Bus Tester 2, the decision
  5. Detection of short circuits in the CAN bus – Error patterns
  6. Exchange service for fieldbus diagnostic devices
  7. Repair, complaint, customs
  8. Retaking of old devices
  9. Suggested bit timing and bus length
  10. Trunk and drop line lengths

  1. 30 days Trial Time
  2. After firmware update, node measurement is displayed as locked
  3. Analyze measurements at your pc
  4. Assignment of D-Sub9 socket on CANtouch and CAN-Bus Tester 2
  5. Background Picture
  6. CAN bus wiring test
  7. CAN Symboleditor Manual
  8. CANtouch does not recognize your special baud rate
  9. CANtouch vs. CAN-Bus Tester 2, the decision
  10. Converting CANtouch Trace Files
  11. Detection of short circuits in the CAN bus – Error patterns
  12. Exchange service for fieldbus diagnostic devices
  13. How is a battery change done?
  14. How to install a software update
  15. Install a license file
  16. Maintenance and Calibration
  17. Pre-defined Node Lists
  18. Problems with drive N1
  19. Protocol Monitor Transmit List
  20. Rating file – adjust rating thresholds individually
  21. SAE J1939 only showing 250kBit/s
  22. Some hints for symbolic decoding
  23. The possible number of screenshots
  24. Which CANtouch-Firmware fits to which CAN-Bus Tester 2 Software ?
  25. Working with projects

  1. CAN Symboleditor Manual
  2. CANvision license model
  3. CANvision Server – Use over a Network
  4. Converting CANtouch Trace Files
  5. Import of CANtouch trace data
  6. SAE J1939 custom PGN decoding
  7. Send list: move message into sequence

  1. CANBUSview XL III, CAN Quick Tester C-QT15 and DeviceNet Analyzer
  2. How to install a new license file
  3. The connection of the CANalarm for programming purposes

  1. 50/60 Hz ripple when the tester is connected
  2. Assignment of D-Sub9 socket on CANtouch and CAN-Bus Tester 2
  3. CAN bus wiring test
  4. CAN Symboleditor Manual
  5. CANBUSview XL III, CAN Quick Tester C-QT15 and DeviceNet Analyzer
  6. CANopen protocol monitor vs. CANopen bus system
  7. CANtouch vs. CAN-Bus Tester 2, the decision
  8. Common Mode Measurement
  9. Connection between firmware – FPGA – PC software (CBT2 does not measure)
  10. Errorframes: which node sent the message
  11. Exchange service for fieldbus diagnostic devices
  12. How to load a new license file
  13. How to use a file with an additional baud rate
  14. Import of CANtouch trace data
  15. Licenses of the protocol monitor are not recognized
  16. ON-LED flashes yellow, no function, not recognized by PC
  17. Problems with the USB connection at the CBT2
  18. SAE J1939 custom PGN decoding
  19. Send list: move message into sequence
  20. Tester shows non existend error-frames
  21. Trigger DSO with the CBT2
  22. Trigger Output CBT2
  23. Which CANtouch-Firmware fits to which CAN-Bus Tester 2 Software ?

CANobserver
  1. Automated control of CANobserver
  2. How to update firmware older than 1.17
  3. Ixxat CANobserver, firmwareupdate not possible
  4. Obsolete Software Download

CAN-Bus Tester
  1. Obsolete Software Download
  2. Product Change Notification CAN-Bus Tester 2
  3. Support of Windows 7/8/8.1/10

Profibus Tester 2

Profibus Tester 3